- This version changed the login authentication method. Please unplug the hard drive before updating firmware. After firmware updated, please press the reset button more than five seconds to reset the router to avoid some compatibility issues.
- Enhanced the login authentication strength and fixed CSRF related issues.
- Forced administrator to change the default password "admin" in internet setup wizard.
- Added protection mechanism for GUI login brute-force attack for login username and password.
- Administrator can assign a specified IP to login GUI in Administration > System > "Allow only specified IP.
- Fixed lease time and lease expires time
- Fixed ethernet connection fail in IPv6 when WAN hwaddr is cloned.
- Fixed allowed and blocked incoming icmp firewall rules.
- Fixed dnsmasq buffer overflow issue.
About Router Firmware:
Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn’t either newer or matching this release.
Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.
In theory, these steps shouldn’t be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don’t always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.
If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.
If you’re looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don’t power off the router or use its buttons during the installation, if you wish avoid any malfunctions.
If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don’t miss the update that will improve your device.
|D-Link DAP-1320 revA2 Range Extender Firmware|
Wireless Range Extender DAP-1320 :More Coverage - Extend the range of your existing Wi-Fi network and eliminate dead zonesPerformance - Up to 300Mbps wireless performance for reliable, everyday performanceBackward Compatible - Compatible with virtually all
|NETGEAR GS105Ev2 Switch Firmware|
New Features & Enhancements:- Added the option to disable/enable power saving mode.- Bug Fixes:- Changed the Flow Control (System > Status > Switch Status) default setting from enabled to disabled.- Fixed the problem where the port 1 will link at 100M inst
|ZyXEL GS1900-8HP Switch Firmware|
Fixes:- [General] After rebooted, unable to save the password which is encrypted with 15 characters- [WebGUI] When configure IPv6 DNS, it will cause display wrong MGNT vlan, and multiple DNS IPv6 address.- [WebGUI] Fix PoE power budget amount display with
|TRENDnet TPE-2840WS v1.0R Switch Firmware|
Changes: - Fixed password lockout issue when modifying admin password- Fixed SSL Poodle Attack security vulnerability- Updated GUI to allow modifying VLAN PVID settings for multiple ports instead of individual- Updated GUI layout to increase/widen viewable
|NETGEAR R7500v2 Router Firmware|
Bug Fixes:- Fixed the issue where multiple PPPoE does not work properly- Fixed the issue where WiFi status always shows “OFF” on web GUI after disabling and then enabling WiFi by pressing the WiFi button on the unit even through WiFi actually w
|ZyXEL VMG1312-B30A Gateway Firmware|
Fixes:- Base on V1.00(AATO.1)b2 source to release V1.00(AATO.1)C0 ANNEX_B version for VMG1312-B30A and modify default romfile for SNMP System Name and Default basic SSID : ZyXEL [latest five bytes of serial number].
|Tenda FH456 (V1.0) Router Firmware|
300Mbps Wireless N Smart RouterTenda FH456 802.11n High-Power WiFi Router is our salute to the medium and large size house. 4x5dBi high-performance omni-directional external antennas and amplifier technology ensure fast, stable and wide range WiFi signal u
|NETGEAR FSM5210Pv1h1 Switch Console Driver|
This package contains the files needed for installing the NETGEAR FSM5210Pv1h1 Switch Console Driver. If it has been installed, updating (overwrite-installing) may fix problems, add new functions, or expand existing ones. Even though other OSes might be co
|ZyXEL ZyWALL USG 300 Security Gateway Firmware|
Fixes: - Add SNMP VPN status and connection counter MIBs. - Default turn off SSLv3 Support in Built-in Service. Using CLI “ip http secure-server sslv3” to turn on it. - Update the bash binary to fix BASH Vulnerability issue, CVE-2014-6271 (orig
|Peplink MediaFast MFA 500 Router Firmware|
Important Notices for Firmware 6.2.1 - Internal Network Firewall Rules Will Need to Be Reconfigured: To increase protection for traffic running between internal networks, Firmware 6.2.1 introduces the new “Internal Network Firewall Rules” table